Command Hooks How To Install

Download Article

Download Commodity

Command Strips past 3M come in multiple types, including hooks with clear strips, other types of hooks, and picture hanging strips. Command Strip hooks can be used to hang a variety of lightweight items, such every bit keys, a clipboard, cord lights or measuring cups. Make sure to choose a suitable surface, and clean information technology with rubbing alcohol before adhering your strips. Information technology's helpful to apply a level and to ask a buddy to help you out when you're determining where to hang items, especially if you're hanging a picture or grouping of pictures you lot want to be straight.

1
Ensure the surface is suitable for the strips. You lot tin employ Command Strips to metal, tile, drinking glass, painted drywall, and painted or varnished wood.^[i] Practice not utilise them to wallpaper, antiques, or valuable/irreplaceable items. Don't use the strips to hang anything over a bed.^[2]
- Avoid using Command Strips on vinyl, since they may not stay adhered.
- If you're using hooks with clear strips, choose a smooth surface.
- To maintain adhesion, employ Command Strips to surfaces that stay between fifty°F (10°C) and 105°F (40°C).
- Avoid hanging command strips directly above a heater since the heat could melt the agglutinative and cause them to fall.^[3]
- Command strips don't typically hold upward well in humid environments, similar in bathrooms.^[4]
two
Ensure the weight of items you're hanging is acceptable. Check the bundle of your product to find its exact weight limit. If your items exceed the weight limit, consider other options such as screws and studs or a moving-picture show cord.
- Command Strips come in a diversity of sizes with different weight-bearing capacities.
- Depending on the product, 3M may advise that you use but one hook per particular you're hanging.^[5]
Advertizement
3
Mensurate and marker the surface. Inquire someone to hold up the item, if possible, so you can stand back and decide if the placement is satisfactory. Use a level to marshal a picture; if it's a group of pictures, use a light amplification by stimulated emission of radiation level. Identify a sticky annotation sideways – like a kite shape – at the peak heart, to a higher place where your item volition hang.^[6]
- Yous may desire to hang a picture 60 inches (152 cm) in a higher place the floor, or with its bottom edge vi to eight inches (15 to xx cm) up from a piece of furniture.
- For a group of items, cut paper patterns of their shapes. Utilise low-adhesive record to identify the papers on the wall and decide where you lot want the items to hang. Then place the corner of a sticky note at the peak center of each paper, so that the bottom corner is your reference point.
4
Clean the surface. Dampen a material with isopropyl rubbing alcohol. Gently wipe the surface where you plan to adhere the strips. Allow the area to dry out.^[7]
- Don't clean the surface with household cleaning sprays or wipes. These leave a residue that tin can brand the strip's adhesion unsteady.
- Control strips won't stick as well if the surface you apply them to is dusty or muddied.^[8]
Advertisement

1

Peel the strips autonomously, if applicative. If y'all have multiple strips, separate them by pulling them away from each other.^[ix]
two
Peel off the blackness liner. Locate the black liner, marked "Wall Side." Hold the unlined portion with one hand as you lot pull the blackness-printed layer off the strip.^[10]
- Yous may need to use your fingernail nether an edge of the liner to brainstorm pulling information technology up.
3

Attach the strip to the wall. Press the sticky side of the strip firmly onto the surface where your hook should hang. Press along the full length of the strip for thirty seconds.^[11]
iv
Adhere the hook to the wall. Peel off the blue liner. Press the claw firmly onto the strip. Go on pressing the hook for 30 seconds.^[12]
- The adhesive volition bail more deeply if you lot strongly printing the hook.^[13]
5

Allow the adhesive cure. Wait at least 1 hour before you use the claw. The agglutinative needs fourth dimension to fully bail to the wall. Its bail will not be every bit stiff if the hook holds weight right away.^[14]

Advertisement

one

Separate the strips, if applicable. If you have multiple strips, pull the strips away from each other to separate them.^[15]
2

Attach the strip to the hook. Pare off the red-printed liner. Line upwards the strip, mucilaginous-side down, with the plate on the behind of the hook. Press firmly along the length of the strip from the elevation down.^[16]
3
Adhere the hook to the wall. Peel the black liner off the strip. Press the claw strongly onto the surface where y'all desire the claw. Hold the hook against the surface for thirty seconds.^[17]
- Pressing the hook firmly allows the adhesive to bond securely.
4
Remove the hook to secure the underlying base of operations. Lift the claw upward to slide it off its mounting base of operations. Button the base strongly confronting the surface for xxx seconds.^[18]
- Pressing the mounting base directly ensures that the adhesive will bond to its maximum strength.
5
Permit the adhesive to cure. Reattach the hook to its mountain by sliding it down onto the base of operations. Don't hang anything on the hook for at to the lowest degree an hour.^[19]
- The adhesive needs time to set against the surface before property any weight.
Advertizing

1

Snap the strips together. Separate the strips by pulling them apart. Align the shapes of the strips, with the cherry-red labels facing outward on each side. Push the strips together until you hear a click.^[20]
two
Attach the strips to the back of the motion picture frame. Peel off i of the red (or green, depending on your product) liners. Place the strip mucilaginous-side downwardly onto the back of the frame. Press the strip downwards firmly.^[21]
- Echo this step for each strip yous want to employ to the frame. For example, you may want to utilise 2 to four strips per frame.
- If y'all're using 4 strips for a frame, put the lowest pair approximately two-thirds of the way down from the frame's pinnacle.^[22]
3

Adhere the frame to the wall. Make sure all of the liners are removed. Push the frame against the wall strongly. Hold it firmly for 30 seconds.^[23]
4
Remove the frame to secure the underlying strips. Concord the bottom of the frame. Lift it gently towards you and upwards. Press the entire length of the strips for thirty seconds each.^[24]
- Don't yank the frame straight towards you, or y'all'll loosen the strips instead of detaching the frame from the wall.
5
Let the strips cure for at to the lowest degree an hour. Don't reattach the frame until an 60 minutes has passed. Afterwards, marshal the frame's strips with the strips on the wall. Push the frame until all of the strips have clicked into place.^[25]
- Leaving the frame off of the wall for an hour gives the adhesive time to bail to the wall.
half-dozen
Readjust the strips if needed. If the frame isn't directly, you can remove one or more strips. Hold the bottom ii corners of the frame and lift information technology up and abroad. Reposition the strip(s) as desired.^[26]
- Hold the top of the strip you want to reposition with one hand. With your other hand, pinch the strip at the bottom and pull it down. Stretch it slowly, straight downwards – upwards to 15 inches – until the strip releases from the wall.^[27]
Advertisement

Add New Question

Question

Can I utilise command strips in a bathroom?

Jason Phillip is a handyman specializing in mounting and hanging objects onto walls. With over five years of experience professionally mounting and installing objects through his company, Jason'due south Handyman Services, Jason'due south work includes working with mounting window AC units, designing art gallery walls, installing kitchen cabinets, and replacing light fixtures on drywall, brick, and plaster. He has been rated a "Pinnacle Pro" every twelvemonth since 2022 past Thumbtack for being one of the highest-rated, virtually popular professionals on Thumbtack.
Question

Why are my command strips falling off of the wall?

Jason Phillip is a handyman specializing in mounting and hanging objects onto walls. With over five years of feel professionally mounting and installing objects through his company, Jason's Handyman Services, Jason's piece of work includes working with mounting window AC units, designing fine art gallery walls, installing kitchen cabinets, and replacing light fixtures on drywall, brick, and plaster. He has been rated a "Summit Pro" every year since 2022 by Thumbtack for existence 1 of the highest-rated, well-nigh pop professionals on Thumbtack.

Support wikiHow past unlocking this expert answer.

Command strips can fall off for a few different reasons. Humidity and excessive heat tin both prevent the adhesive from sticking to surfaces. Also, it'south of import to push button them all the way into the wall when you're applying them or they could autumn off.
Question

Tin I utilize command strips on a cement wall?

Jason Phillip is a handyman specializing in mounting and hanging objects onto walls. With over v years of experience professionally mounting and installing objects through his company, Jason's Handyman Services, Jason'south work includes working with mounting window AC units, designing fine art gallery walls, installing kitchen cabinets, and replacing light fixtures on drywall, brick, and plaster. He has been rated a "Acme Pro" every twelvemonth since 2022 past Thumbtack for being one of the highest-rated, well-nigh popular professionals on Thumbtack.

Support wikiHow by unlocking this practiced answer.

Control strips aren't going to piece of work that well on a cement wall considering cement is dusty and the dust won't let for the gum to stick that well. Your best pick is to use a hammer drill to drill into the wall, put an ballast into the wall, and then screw into it.